Bookmark and Share Email this page Email Print this page Print

Lassoing a mooring

Sep 1, 2015

It seems everywhere we go, there is a different method of tying to a mooring. Sometimes the mooring buoy has the pennant attached to the top of it; sometimes there is a pick-up buoy attached to the mooring pennant; sometimes there is only one mooring pennant, sometimes two; sometimes the pennant will fit through our hawse holes, sometimes not. It is usually a surprise until we get the lines out of the water and figure out how we should be making fast to the mooring.

When picking up a mooring, we approach the mooring ball into the wind, and I try to stop Nine of Cups just past the pennant. Marcie is at the bow with the boat hook and a dock line at the ready, and her job is to get us attached to the mooring any way she can. Once we are attached, no matter how tenuously, we can take our time and sort out how best to make fast to the mooring. If conditions are good, the mooring has a pick-up buoy floating next to it and no one is watching, we can usually pick it up and secure it on the first try. If the wind is gusting, there is no easy way to pick up the pennant and/or there are other boats to maneuver around, it sometimes takes a few tries. The number of tries it takes is also directly proportional to the number of people watching. I think our record is 13 attempts at the Harlem Yacht Club, when everything went wrong and there were dozens of people watching how these sailors from Colorado go about picking up a mooring. They are probably still chuckling about that bit of evening entertainment 12 years ago.

When there is no pick-up buoy, the process is much more difficult. Sometimes there is just a big round mooring ball floating there with the pennant attached underneath. Other times, there is a ring at the top of the mooring ball. Cups has too much freeboard at the bow to reach the mooring ball, and there is usually no hope of picking up the entire ball with the boat hook. I learned this method of picking up the mooring from another cruiser, and it works quite well.

We attach one end of a dock line to the boat, tie a very large bowline (6 to10 feet in diameter) in the other end of the dock line and route it through the lifelines and outside everything. The dock line should be the sinking variety — polypropylene floats won't work — and should be long enough that the entire bowline will reach the water with a few feet to spare. When the boat comes alongside the mooring ball, Marcie simply drops the bowline over the ball. The line will sink and, as the boat drifts back, the bowline will constrict around the chain or rope under the mooring ball. Then we keep tension on the dock line as the mooring ball is pulled up to the boat and we figure out how to attach the boat to the pennant.

Edit Module

Old to new | New to old
Sep 1, 2015 03:01 pm
 Posted by  Blueboyou

Great idea. We had exciting times in St. Barts with 18-25 kt winds trying to secure a mooring ball. I was black and blue from trying to hold the mooring line without being pulled overboard (bad idea). Since we anchor 100% of the time, this was a true baptism by fire. Thanks for sharing.

Sep 1, 2015 03:08 pm
 Posted by  Allen J

I like your suggested loop over the entire mooring ball. I think it would also work if you simply attached one end of a dock line to the bow cleat and threw a large loop over the mooring ball, let the line sink below the ball and then pulled in on the free end of the line. I think it should work the same as your large bowline loop to let you pull the mooring ball close to the boat to allow securing a line through the mooring ring on top of the ball. A. J. Wright

Sep 1, 2015 03:33 pm
 Posted by  Pete on Delphinus

Great description of a simple method. Pete

Sep 1, 2015 06:16 pm
 Posted by  OceanWanderer

Having picked up a mooring many, many times solo and under windy conditions, I can attest (just as Allen J has guessed) a large bight dropped over the ball and both ends of the line made fast to the vessel works best. On a few occasions when conditions made it impossible to keep the bow near the ball long enough, I have backed up to the ball letting the boat weather vane and dropped the bight (made off to the stern) over the mooring, allowing me to attach a line from the bow and then releasing the stern. John C

Sep 1, 2015 09:08 pm
 Posted by  AlainB

I like it and it most likely would work on our experience this summer. We were at Niagara-On-The-Lake, on the Niagara River with 2-3 knots of current and 20+ knots of wind with about 150˚ opposite to the current. Rhéa is 41’ and has more than 4 foot of freeboard, even with the bow thruster I was making a foul of myself. After many attempts my wife jumped in the dingy and passes a long floating dock line through the buoy ring. It was then simple to get close enough to catch the line with the boathook. Alain B

Sep 2, 2015 12:21 pm
 Posted by  Tom C.

Two comments. The first is certainly true for a power boat and may or may not be true for a sailboat still under sail. Put the stronger person on the bow and the brains on the wheel! The second is that for a ball with a bail on top, Robship makes a very interesting hook and moor boat hook pole which lets you pass a line through the bail without leaving the boat. Tom C

Add your comment: