Bookmark and Share Email this page Email Print this page Print

A useful canvas bucket from old sails

Oct 25, 2012

Call me a pack rat, but I hate throwing anything away that could still have some use aboard. My husband David uses old line to make ocean plait rugs. I use old jacklines to keep jerry jugs firmly in place on deck and also as hoists when making courtesy flags. So when it came time to buy a new mainsail, I couldn't just throw the old one away. Though the sail had seen several thousand miles and many years of use, it had some life left in it. I carefully cut out large useable chunks for future use and tucked them away for a rainy day project. Over the years, I've found lots of uses for used sail material beyond mending and patching working sails in a pinch.

Sewing the plastic disc between two pieces of sail canvas.

Hand stitching the rim over quarter-inch lifeline.

The first project I attempted with old sail canvas was a life raft cover. When we're in port, we use it to provide some UV protection to the raft. I'm not a particularly good seamstress, but straight stitching isn't difficult and the raft case is basically rectangular, so coming up with a pattern wasn't difficult and the results were definitely acceptable.

The absolute best project, however, was a versatile canvas bucket. When we bought Nine of Cups, there was a canvas bucket aboard which we used regularly for washing decks and general clean-up. It was easy to toss overboard, fill with seawater and haul back aboard. The original one was getting old and lost more water than it held. David suggested that we could buy a new one or maybe I could put my new SailRite sewing machine to work and sew a new one. It looked simple enough and I had the time, so I thought I’d give it a go. Whenever an existing pattern is available, the process is much easier.

There were two things we didn't like about the existing bucket, so I decided I'd implement a couple of changes. First, it sometimes collapsed when we tossed it overboard to fill it with seawater and second, it was so lightweight, it sometimes just skipped over the water and wouldn’t fill at all. I decided if I could make the top rim and the bottom more rigid, it would have enough extra weight to sink below the surface while keeping the top open for easy filling without collapsing.

I cut a rectangular piece of sailcloth 31.5 inches by 12 inches. To make the bottom rigid, I found the flat lid of an old plastic crate and using a pencil with a string attached, measured, marked and cut out an 11-inch diameter circle. I later thought that cutting out the bottom of an old plastic pail that had a crack in its side would have been just as easy.

I then traced the plastic circle onto sailcloth and cut out two slightly larger (half-inch all around) circles, which would allow for a seam allowance and room to maneuver. I sewed the plastic disc between the two pieces to keep it in place.

David Lynn tests the new canvas bucket.

The next step was to form a tube with the 31.5-inch rectangle and sew along the side. Though I have a heavy-duty SailRite sewing machine, this project could be done successfully with a lightweight machine as well. Checking that all seams were facing out, I pinned the encapsulated disc to one end of the canvas tube. This is a tricky process because there seems to be too much material for the disc. I initially used four attachment spots and then spaced the pins so that the material was evenly distributed. I used a zipper foot, rather than a standard presser foot in order to sew as closely to the plastic disc as possible. It started to look like a bucket.

The top rim needed to be finished and it needed a handle, of course. I used two 6 inch strips cut from old 1-inch jackline webbing and sewed them on opposite sides of the buckets spaced about 1 inch from the top rim. This reinforcement would accommodate full buckets of water without the weight tearing out the sides of the bucket. I installed two brass grommets spaced 3 inches apart on each strip, which would accommodate a rope handle. It was important to do this step before completing the rim to ensure that I could get the fabric under the sewing machine needle.

In order to make the rim rigid, I employed a 31-inch piece of old quarter-inch lifeline (any stainless wire, about a quarter-inch, would work just as well) and hand stitched it inside the rim by folding the 1-inch of canvas I had allowed above the handle reinforcement strips over the wire.

I attached lengths of rope to each side of the bucket to act as handles and knotted them securely through the grommets. I later tied another piece of line connecting the handles so the bucket could easily be tied to the aft lifeline for convenient access and use. Without much effort and an investment of less than two hours, we had a new canvas bucket.

-------------
Marcie Connelly-Lynn lives aboard Nine of Cups, a Liberty 458 cutter, with her husband David.  
 

Mar 24, 2013 12:20 pm
 Posted by  Sailingfar

Love this clever, re-purposing project. This one is good for land or sea. I can see me using in in the vegetable garden.

Add your comment: